Forensic Engineers and Consultants

Tag Archive: machine design

  1. Machine Guarding and Risk Assessment

    Leave a Comment

    The Occupational Health and Safety Administration (OSHA) “Top 10 for 2018” violations once again have Machine Safeguarding earning a position on the list. Machine safeguarding was the 9th most cited standard as noted in the list below:

    1. Fall protection, construction (29 CFR 1926.501)
    2. Hazard communication standard, general industry (29 CFR 1910.1200)
    3. Scaffolding, general requirements, construction (29 CFR 1926.451)
    4. Respiratory protection, general industry (29 CFR 1910.134)
    5. Control of hazardous energy (lockout/tagout), general industry (29 CFR 1910.147)
    6. Ladders, construction (29 CFR 1926.1053)]
    7. Powered industrial trucks, general industry (29 CFR 1910.178)
    8. Fall Protection–Training Requirements (29 CFR 1926.503
    9. Machinery and Machine Guarding, general requirements (29 CFR 1910.212)
    10. Eye and Face Protection (29 CFR 1926.102)

    (Source: www.osha.gov/Top_Ten_Standards.html)

    (more…)

  2. Case Study: Fatality Servicing Unsupported Excavator Boom

    Leave a Comment

    A mini-excavator at a job site developed a leak at a hydraulic fitting at the base of the cylinder that raises and lowers the boom. A subcontractor foreman at the site raised the boom to search for the leak. The foreman found and attempted to tighten the leaking fitting. When he did, the fitting separated from the base of the cylinder, releasing the hydraulic pressure that held the boom aloft. The boom fell and the bucket struck a nearby superintendent for the general contractor.

    (more…)

  3. Defective Vertical Baler Causes Serious Crush Injury to Operator’s Arm

    Leave a Comment

    I recently worked on an interesting case involving a box baler. An employee of a butcher shop put some empty cardboard boxes in a vertical box baler and pushed the control switch to compact the boxes. After the 30 by 60 inch platen weighing 851 pounds returned to its raised position, the employee reached into the open space above the bottom door on the baler and began to clear cardboard from the bale tie slots in the bottom of the raised platen. Suddenly, and without warning, the steel pin attaching the platen to the raised hydraulic cylinder rod failed. The heavy steel platen fell and crushed his arm which was outstretched over the baler door into the compaction space.

    (more…)

  4. Improper Design Leads to Fatigue Failure In Blower Shaft

    Leave a Comment

    A blower used to exhaust air from an industrial process stopped functioning when the blower wheel drive shaft fractured.  The process, and thereby most of the plant, had to operate at a reduced volume until the blower wheel could be replaced.  The blower wheel had been installed during a shutdown a week before the incident.  The blower wheel was a spare installed when the existing blower wheel was sent for scheduled remanufacturing. (more…)

  5. Case Study of an Injury Involving a Soil Mixer

    Leave a Comment

    In May, 2014, a plant farm worker was seriously injured when he fell into the hopper of an electrically powered soil mixer.  The mixer in question used a rotating steel ribbon powered by a 7-1/2 hp electric motor to mix batches of materials such as sand, mulch, wood shavings, fertilizers and other landscaping materials to create potting soil. At the top of the hopper sidewalls, within 6 inches of the ribbon, was a steel grate. (more…)

  6. A Case Study in a Coal Mine: What are a Machine Rebuilder’s Responsibilities?

    Leave a Comment

    In November of 2010, a miner was injured by a roof bolting machine (roof bolter) in an Alabama underground coal mine. The roof bolter in question had undergone a complete rebuild intended to return the machine to the original equipment manufacturer’s (OEM’s) specifications. Warren was hired to analyze both the design of the roof bolter and the actions of the rebuilder to determine if either contributed to the unfortunate coal miner’s serious injury. Background information on coal mining and roof bolters, as well as an analysis of the roof bolter and the actions of the rebuilder are included. (more…)

  7. Manufacturer Settles with Operator Injured by a Flying Tool Fragment from Milling Machine

    Leave a Comment

    In my June 2015 blog, I discussed a personal injury case where the jury decided that the lack of interlocks on the covers of a swamp cooler did not render it defective, even though it was technologically feasible to do so and their existence would have prevented the amputation.  Conversely, in another interesting personal injury case involving a computer numerically controlled (CNC) milling machine, a large settlement was made by the manufacturer with the injured operator because the machine did not have adequate interlocks on its enclosure doors. (more…)

  8. Jury Claims Swamp Cooler is Not Defective; Interlocked Guards are Not Required

    Leave a Comment

    An evaporative cooler, also known as a “swamp cooler”, is an air conditioner that works by evaporating water.   A float valve keeps several inches of water in the bottom of the unit. A pump takes water from the pan to the top of a series of vertical pads made of absorbent materials like wood fibers. The water flows by gravity through the fiber pads. A fan pulls hot air from outside the house through the soaked pads. Water in the pads evaporates, cooling the air and increasing its humidity. The cooled and humidified air is blown back into the house. Evaporative coolers need to be cleaned periodically. (more…)

  9. Forensic Examination of Losses that Include Programmable Logic Controllers (PLC’s)

    Leave a Comment

    Many modern machines and processes are controlled by Programmable Logic Controllers (PLC’s).  PLC’s are essentially computers that have the ability, properly connected and programmed, to interface with the outside world and control the actions of a machine like a robot or conveyor.  The PLC has a processor for processing the user programmed logic, and also has input / output (I/O) wiring provisions for both analog (e.g. temperatures and pressure transducers) and digital (e.g. limit switches and indicator lights) devices.  (more…)

  10. Desk Reviews Answer Subrogation Questions

    Leave a Comment

    An important question concerning a workers’ compensation claim involving machinery and equipment is whether or not the loss can be subrogated to a responsible third party. In order to properly analyze this question, it is often helpful to have an engineer determine if the machine contains a condition of defect that caused the incident. One effective way to move ahead with confidence  — and without investing travel time and money into a full investigation — is a Warren desk review. (more…)

Type ofLoss

Not sure what you're looking for?
Browse All

Select Loss Category
Select Sub-Category (choose category first)
View Now