Forensic Engineers and Consultants

Tag Archive: Jeffrey H. Warren

  1. Jury Claims Swamp Cooler is Not Defective; Interlocked Guards are Not Required

    Leave a Comment

    An evaporative cooler, also known as a “swamp cooler”, is an air conditioner that works by evaporating water.   A float valve keeps several inches of water in the bottom of the unit. A pump takes water from the pan to the top of a series of vertical pads made of absorbent materials like wood fibers. The water flows by gravity through the fiber pads. A fan pulls hot air from outside the house through the soaked pads. Water in the pads evaporates, cooling the air and increasing its humidity. The cooled and humidified air is blown back into the house. Evaporative coolers need to be cleaned periodically. (more…)

  2. Desk Reviews Answer Subrogation Questions

    Leave a Comment

    An important question concerning a workers’ compensation claim involving machinery and equipment is whether or not the loss can be subrogated to a responsible third party. In order to properly analyze this question, it is often helpful to have an engineer determine if the machine contains a condition of defect that caused the incident. One effective way to move ahead with confidence  — and without investing travel time and money into a full investigation — is a Warren desk review. (more…)

  3. Harmless Appearing, Smooth Rotating Mixer Shaft Causes Serious Finger Amputation Injuries

    Leave a Comment

    I recently finished working on a case where an operator received a right hand injury when an unguarded, rotating mixer shaft caught his gloved hand between the right index finger and middle finger, twisting it around the shaft causing the index finger to separate from the hand and the middle and ring finger to be dislocated.  The mixer contained an unguarded rotating shaft, which created an uncontrolled motion hazard when rotating at speeds up to 450 RPM. (more…)

  4. Uncontrolled Hazards and Risk Assessments — Part One

    Leave a Comment

    Machine equipment manufacturers are called upon to study potential risks of equipment before selling it in the marketplace. In addition, ANSI machine tool standards further address equipment hazards and risks that cannot be eliminated by design. In one case I investigated, the depth of that critical risk assessment became an important factor in a claim involving a machinist blinded while using a computer numerically controlled (CNC) machining center. (more…)

  5. Winter Safety Tips for Portable Electric Generators

    Leave a Comment

    During winter ice storms, power to residences is often lost and homeowners revert to using gasoline powered portable electric generators.  It is often thought by some homeowners that leaving a generator outside in the severe weather may damage it or affect its performance and therefore resort to bringing the unit inside the shelter, typically, the garage. This is particularly hazardous when the generator is run for an extended period of time as carbon monoxide (CO) poisoning from the toxic exhaust gas can cause death. In addition, other hazards including electric shock, electrocution, fire and burns potentially can occur. (more…)

  6. Preventing Fugitive Vapor Explosion with Design

    Leave a Comment

    For years, many water heater-related fires, injuries, property damage claims, and deaths were attributed to “consumer misbehavior.” By 2002, however, the NFPA National Fuel Gas Code began to reflect several key realizations: the existence of fugitive vapors and how appliance design can limit the risks they pose. (more…)

  7. Code Violations Are Root of Fatal Explosion

    Leave a Comment

    The design and installation of gas piping systems in homes and commercial buildings is guided by a set of regulations called NFPA 54 — the National Fuel Gas Code. The code, which establishes minimum safety requirements, is also used by forensic engineers to evaluate an explosion to determine cause and responsibility. (more…)

  8. Design Can Prevent Industrial Accidents

    Leave a Comment

    Two of the top causes of workplace accidents, according to the United States Department of Labor’s Occupation Safety and Health Administration, are a lack of machine guarding and improper control of hazardous energy. At first blush, these types of incidents can mistakenly be attributed to an employee’s actions without considering how a machine’s design or the improper control of an environment or situation may have contributed.
    (more…)

  9. Machine Safeguarding for an Imperfect Workforce: Humans.

    Leave a Comment

    Every day more than 12 people in the United States lose their lives in workplace injuries, according to U.S. Department of Labor data. In 2011, OSHA estimates, 3.3 million people suffered a workplace injury from which they may never fully recover. Two of the top ten most frequently cited OSHA standards that result in injuries and death are lockout/tagout and machine guarding. (more…)

Type ofLoss

Not sure what you're looking for?
Browse All

Select Loss Category