Forensic Engineers and Consultants

Category Archive: Safety and Design

The Impact of Technology on Slip and Fall Incidents

I have investigated hundreds of slip and fall incidents in my career. Today, we have new tools and technology available to assist investigators in conducting forensic investigations to determine the cause or causes of these incidents and to assist owners and operators in loss preventions efforts to minimize the potential of slip and fall incidents. Read More

New 2017 Edition of NFPA 921 Guide for Fire and Explosion Investigations

Author

Over the course of its 25-year history, NFPA 921 Guide for Fire and Explosion Investigations has changed the practice of fire investigation for the better.  Without a doubt, NFPA 921 has appropriately driven a more rigorous approach to fire investigation that seeks to avoid cognitive bias and reliance on techniques that, when rigorously examined, are little more than pseudoscience.  One need look no further than the Cameron Todd Willingham matter, wherein a Texas man was executed in part based on a flawed fire investigation, to understand the importance of conducting a proper fire investigation. Read More

Grounding versus Bonding – Understanding the Difference in Building Electrical Systems

Author

While a teenager might be very familiar with being “grounded”, there is confusion over the meaning of the word in the electrical sense. In building electrical systems, “grounding” and “bonding” are two terms that are often misunderstood. Improper application of the concepts of grounding and bonding may create lethal shock and fire hazards. “Earthing” is a term which comes from the European International Electrotechnical Committee (IEC). Earthing is synonymous with grounding but often thought to have a different meaning. Read More

Injury Involving a Capstan Winch

A capstan winch uses a mechanically powered rotating cylinder, called a capstan, to apply pulling force through a rope. When the rope is looped around the rotating capstan and tightened, friction between the rope and capstan allows the winch to apply force to pull a load. A typical capstan winch is shown in Figure 1 below. Read More

Improper Fireplace Construction: Testing the Impact of Non-Compliant Clearance to Combustibles

Author

As the weather turns cold, many people use fireplaces to provide supplemental heat. The warmth from a fireplace is a comfort and the aesthetics of a glowing fire are a pleasure.  However, there is nothing pleasurable about a residential house fire that results from an improperly built or used fireplace or chimney. Read More

Defective Clevis Pin Culprit in Runaway Trailer

Author

A large agricultural trailer had been connected to a truck using a clevis pin with a spring locking clip.  The trailer became disconnected from the truck and collided with an oncoming vehicle.  The trailer was in poor condition, did not have safety chains, and had substantial recent modifications by the owner. Read More

Are You Prepared for Emergencies? Your Generator Set Should Be!

Author

Emergency generators are often called into service during catastrophic events like hurricanes, floods, tornadoes or fires, but also during more mundane events like thunderstorms and other things that may temporarily interrupt the public power grid. Can you rely on your generator to perform at those critical times? Read More

Case Study of an Injury Involving a Soil Mixer

In May, 2014, a plant farm worker was seriously injured when he fell into the hopper of an electrically powered soil mixer.  The mixer in question used a rotating steel ribbon powered by a 7-1/2 hp electric motor to mix batches of materials such as sand, mulch, wood shavings, fertilizers and other landscaping materials to create potting soil. At the top of the hopper sidewalls, within 6 inches of the ribbon, was a steel grate. Read More

A Case Study in a Coal Mine: What are a Machine Rebuilder’s Responsibilities?

In November of 2010, a miner was injured by a roof bolting machine (roof bolter) in an Alabama underground coal mine. The roof bolter in question had undergone a complete rebuild intended to return the machine to the original equipment manufacturer’s (OEM’s) specifications. Warren was hired to analyze both the design of the roof bolter and the actions of the rebuilder to determine if either contributed to the unfortunate coal miner’s serious injury. Background information on coal mining and roof bolters, as well as an analysis of the roof bolter and the actions of the rebuilder are included. Read More

Painting of Handicap Ramps

As an experienced safety consultant, I’m called on to investigate a wide range of premises liability incidents. One common premises liability incident that often results in serious injury is a fall on a handicap ramp. There are at least four types of handicap ramps – flare side, parallel, returned curb and built-up. Read More

Type ofLoss

Not sure what you're looking for?
Browse All

Select Loss Category