Forensic Engineers and Consultants

Archive: Inland & Ocean Marine

Ammonia

Ammonia – The Good, The Bad, The Smelly… Part One

Author

Ammonia is a compound consisting of one nitrogen atom and three hydrogen atoms and is denoted by the formula NH3. Its boiling point is -28°F at atmospheric pressure, so unless it is under pressure, it is gaseous at room temperatures. Therefore, pure ammonia is typically stored under pressure in a liquid form. Household ammonia is only 5-10% NH3, the remaining 90-95% is water. Ammonia is extremely soluble in water. It is often depicted  like this: Read More

Crane Incident Handbook

Author

Cranes are powerful lifting devices that we see everyday in construction areas, shipping terminals, and industrial sites. They are so common that we often pass by them with little thought. Cranes, however, can sometimes become involved in incidents that injure people or damage equipment. Read More

Machine Guarding and Risk Assessment

Author

The Occupational Health and Safety Administration (OSHA) “Top 10 for 2018” violations once again have Machine Safeguarding earning a position on the list. Machine safeguarding was the 9th most cited standard as noted in the list below:

  1. Fall protection, construction (29 CFR 1926.501)
  2. Hazard communication standard, general industry (29 CFR 1910.1200)
  3. Scaffolding, general requirements, construction (29 CFR 1926.451)
  4. Respiratory protection, general industry (29 CFR 1910.134)
  5. Control of hazardous energy (lockout/tagout), general industry (29 CFR 1910.147)
  6. Ladders, construction (29 CFR 1926.1053)]
  7. Powered industrial trucks, general industry (29 CFR 1910.178)
  8. Fall Protection–Training Requirements (29 CFR 1926.503
  9. Machinery and Machine Guarding, general requirements (29 CFR 1910.212)
  10. Eye and Face Protection (29 CFR 1926.102)

(Source: www.osha.gov/Top_Ten_Standards.html)

Read More

Unguarded Shear Point on Force Tester Amputates Worker’s Finger

Author

A worker was injured while testing gas springs similar to the type that hold the hatchback of an SUV open. The hazard that injured the worker was an unguarded shear point. The tester contained a mounting plate that was raised and lowered by a pneumatic cylinder.

The pneumatic cylinder lowered the mounting plate while the worker’s fingers were in the hazardous, unguarded shear point. Read More

Hazards Can Lurk Anywhere … Watch Your Step …

Author

While on a lunch stop during a recent vacation trip through Tennessee, I happened across a safety hazard that required immediate attention.  The establishment had a raised concrete patio at the front with a steel railing around the perimeter.  At one edge of the patio was a set of stairs with a continuation of the steel railing used as a handrail.  The top edge of the patio had light strings wrapping the top metal bar as accent lighting for the perimeter.  The light string continued down the stair handrail wrapped in the same manner as the rest of the patio. Read More

Case Study: Fatality Servicing Unsupported Excavator Boom

Author

A mini-excavator at a job site developed a leak at a hydraulic fitting at the base of the cylinder that raises and lowers the boom. A subcontractor foreman at the site raised the boom to search for the leak. The foreman found and attempted to tighten the leaking fitting. When he did, the fitting separated from the base of the cylinder, releasing the hydraulic pressure that held the boom aloft. The boom fell and the bucket struck a nearby superintendent for the general contractor.

Read More

Testing As Part of Gas Appliance Incident Investigation

Author

Equipment and appliances supplied with fuel gases like natural gas, propane and butane are a common and convenient part of most of our lives.  Such devices as gas grills and ranges, ovens, furnaces, space heaters and water heaters usually perform without incident.  However, when they malfunction the potential for incidents such as fires and explosions, carbon monoxide (CO) poisoning and burn injuries may occur. These incidents may be due to design and manufacturing defects in the product, or improper installation or operation of the device.

Read More

Defective Vertical Baler Causes Serious Crush Injury to Operator’s Arm

Author

I recently worked on an interesting case involving a box baler. An employee of a butcher shop put some empty cardboard boxes in a vertical box baler and pushed the control switch to compact the boxes. After the 30 by 60 inch platen weighing 851 pounds returned to its raised position, the employee reached into the open space above the bottom door on the baler and began to clear cardboard from the bale tie slots in the bottom of the raised platen. Suddenly, and without warning, the steel pin attaching the platen to the raised hydraulic cylinder rod failed. The heavy steel platen fell and crushed his arm which was outstretched over the baler door into the compaction space.

Read More

Graphitic Corrosion – Difficult to determine before a failure!

Author

Graphitic corrosion is a process that may happen in equipment made of iron, particularly grey cast iron, but also ductile cast iron. Graphitic corrosion can lead to unexpected catastrophic failure of the affected part because the cast iron can lose its strength without a visible warning such as a change in size, shape, or appearance. Read More

Defective Clevis Pin Culprit in Runaway Trailer

Author

A large agricultural trailer had been connected to a truck using a clevis pin with a spring locking clip.  The trailer became disconnected from the truck and collided with an oncoming vehicle.  The trailer was in poor condition, did not have safety chains, and had substantial recent modifications by the owner. Read More

Type ofLoss

Not sure what you're looking for?
Browse All

Select Loss Category
Select Sub-Category (choose category first)
View Now